Search results

I'm making a second trip to range for higher load workup on 75 HHT in 20.5" Sako 85 Carbonlight (10 twist) using Varget. I might also try some N540 to see how fast that can go. I'll report back soon.

half MOA is pretty darn good. Do you mind sharing info on your load workup so far; assuming with H4831SC? I had tried that powder with 151HHT in my other x-bolt (24") barrel and I though that it pressured out before 2900 fps but the gun was new and so I'm going to try the powder again.

For comparison I’m running the 160 HHT at 3012 fps in 26” x-bolt with Ramshot Magnum.

Put my order in today.

Not much data available so I thought I’d try increasing charge weights with three powders to see what velocities I get as I approach pressure. 5 to 6 grain increments (edit: increments were 0.5 to 0.6 grains). I thought I’d have it covered but will need to go back with higher charges for two...

Wouldn’t the VV website starting load of 61 gr N165 for 200 gr Nosler partition be closer? Actual weight of 199gr HH is 197. Maybe work up from there for pressure then back up and try a group.

I've just started annealing (torch + deep socket) and mandrel neck expanding (21st Cent.). I loaded a few 280AI and could feel the improved consistency when seating the bullets even with the RCBS rock chucker press. My Redding sizer die was easy as I just removed the expander ball sleeve. My...

For my 6.8 Western x-bolt I used Ramshot Magnum with 156HH and went up to 3030fps. I’m now using 160HHT with Ramshot Magnum and get 3050 fps. My last session with the rifle was 1-mile steel. Took more than a few shots though to walk it in. I briefly tried H1000 but seemed slower? I’ve not...

6.8 Western might not be limited by your mag length, and getting 3050 fps with 160gr HHT. 300 WSM is a solid choice but will the bullet fit through your existing supressor?

The author had interesting comment as part of the conclusion: "The theory of vibration nodes timed with bullet exit seems logical when an accomplished shooter and reloader is confidently lecturing you on the subject. But if this were true, your perfect node load would go out the window with any...

Just today I had some flyers which I attribute to me not consistently settling behind the gun. I have a habit of standing up and walking around after each shot. I take notes, let barrel cool, etc. Each time I sit down for the next shot there is risk of changed position (cheek weld, rear bag...

Koda. I’m going to suggest there is nothing wrong with the Inflex recoil pad. The factory bedding job is a maybe. I have two x-bolts and they are my only rifles that I have not done a custom epoxy bedding on (excepting a Savage composite stock with internal aluminum chassis). Both x-bolts...

On my 280 AI I switched from Nosler brass to Peterson brass and found the Pederson to be heavier in weight and requiring a lower powder charge compared to Nosler brass. Although the 3200 fps for the 140 gr AH doesn't stand out as too high. Technique- If the x-bolt is a lightweight rifle...

I use Grip-n-pull and always squeeze the handles with a long pliers to get more leverage. I also have to use one size smaller on the bullet diameter holes otherwise it slips. Bullet do get marred but I always find a use on those at the range and they seem to shoot well enough at 100 yd.

300 PRC here with H1000 on 8 twist. I started with the 199 HH at 3080 fps. I've run the 203 HHT also to 3080. I'm currently running the 182 HHT at 3280 to 3330 depending on which charge weight I settle on. All are about 0.5 MOA at 200 yards.

I had a load with 199 HH (.308) and tried some 203 HHT. I did start lower but worked up to the same powder charge; which I think was below pressure signs anyway. The same powder charge with the HHT bullet (which is 6 grains heavier than the HH bullet) yielded a muzzle velocity about 15 fps...

Welcome from SF Bay Area CA. I tried a bunch of different 7mm bullets in our 280 AI's; a right hand for me and a left hand for my son. Mostly settled on 132 HHT in the 7mm. Should cover most game except maybe elk, where I might have him go heavy with 7mm lead core bullet while I'd likely use...

300 PRC 182 HHT H1000 CCI #250 ADG (fired x5) COAL = 3.630” Lee FCD 26” 8” Twist X-Bolt Pro Start 80.8 - 3120 fps End 85.4 - 3280 fps (I will try higher charges next) 0.5 MOA at 200 yards. Single digit ES Stability Factor 2.12 280 AI 132 HHT H4831SC CCI #200 Peterson (fired x3) COAL...

My pops showed me how to reload probably in 1978. After a couple decades lapse (family and work) I just started up again a few years ago after retiring. We talk on the phone and he gets a chuckle when I mention some of the new reloading tricks that I am trying. I've settled on a decent load...

I've already made some posts, but new here. I have enough Hammer Bullets purchased to buy a nice rifle! But they are hard to resist. Currently working on three cartridges: 300 PRC with a great load on 199 HH but migrating to 182 HHT and/or maybe 203 HHT. 6.8 Western, just going with 160...