Share Your Hammer Loads

joe16 said:
Muddy

Did you try h4350 with the 154 in your short mag?

Just wondering if it's performance would be on par as it did with its bigger brother.

Go Buckeyes🤣🤣🤣
Click to expand...
My prob is almost out of the 154's and need to finish off in 300WM. H4350 is prob going to be case capacity issue versus short COAL in my rifle. If I have enough boolits to try, will do.

Go Orange!
 
7mm-08
Aero M5/AR10
18" Wilson Combat 1/9 T
New PPU cases
Light taper crimp 2nd PDR
CC #34
2.810 COL
80 F.
750ft. ELE

120 HH

.3 & .4 MOA:

TAC - 43gr @ 2975fps 6 SD
N135 - 40.5gr @ 2880fps 2 SD (Edited to add: 50rnds fired with 9 SD!)
N135 - 41gr @ 2920fps 9 SD
IMR3031 - 41.5 @ 2950fps 6 SD

All showed ejector smears. Fire & Forget brass. Not a concern.
N135 needs a 41.5gr test. Data to follow Edited: Over pressure. 41gr N135 max. 40.5gr Accuracy load.
 
Last edited:
Remington 700
223 Remington
24” 1:12 twist
44 grain hammer hunter
COAL 2.190
Remington 3X fired brass
Primer - CCI br-4 SRP
Powder- Benchmark
26.5 @ 3485 fps
27 @ 3613 fps
27.5 @ 3672 fps
28 @ 3704 fps
28.5 @ 3736 fps slightly compressed
Note - no sign of pressure. Settled on 28.2 grains @ 3715 fps
 
Last edited:
308win
Mauser 98
Shilen 24" 10" twist
130sh
Wlr primers
col 2.630
r-p brass
crimped 1/4turn
varget 48.5 gns
3118 fps av.

308win
Ruger 77 mkll 22" barrel twist?
130sh
Winchester brass
Wlr primers
Crimped 1/4turn
Cfe223
52gn -3073
52.5 -3097
53gn -3067
53.5 -3089
54gn -3130. 3/4moa @54gn.
 
88gr Hammer Hunter 6 Remington Ackley, 7.5 twist Krieger, Kelblys Atlas Tactical, McMillan Game Hunter stock. N160 51.5gr at 3565 fps shot at 600 yds under .5 moa. Shows no pressure signs at all could go higher but shoots really well with this load. also it is a 26" barrel and using BR2 primers loaded .010 off rifling. Brass is made from 7x57 Nosler. I have also recently for another 6 Rem ai made brass from Lapua 8x57 Mauser brass and really came out nice
 
Last edited:
Thank you! I bet you had some trimming and probably neck turning to do with moving that much brass😄
 
Remage 700LA
Skinny ugly - .270Win aka .270 Thors Hammer
27" Preferred Barrel, Light Palma, 1:8tw, 0.290 freebore, 5R
Peterson brass 2x
FM210
160HHT
CBTO - 3.015
COAL - 3.655
Jump - 0.025
LeeFCD Crimp 1/8
Alliant RL26
58.0 - 3079
59.0 - 3100
60.0 - 3167 ejector
61.0 - 3212 ejector, primer crater

Going to try couple ideas. I was hoping for bit more.
 
Last edited:
You must log in or register to reply here.
Back
Top